![]() ![]() Often, parts of the print that were less than one line thick would not be able to print at all. The result was that when slicing a file, if part of the print was two-and-a-half lines thick, two lines would be generated, with a small gap left in between those two lines. In the past, sliced files would use a consistent line width, with the exact width depending on the nozzle diameter and the line width settings used. The first and biggest improvement in Ultimaker Cura 5.0 is the revolutionary new slicing engine that unlocks variable line widths when slicing files. Finer, smarter, and faster prints with our new and improved slicing engine ![]() It will be live and you can ask any questions to our CTO, Miguel Calvo.With this release, we’re excited to say that you can expect some of the biggest improvements the software has ever seen! including increased print quality when printing fine details and thin walls, stronger printed parts, and reduced print times for users of Ultimaker printers. We’re hosting a free tech demo on February 7. Reliable bed tilt compensation (no more thumbscrews) 2.4 and 5 GHz Wi-Fi A 1080p camera (mounted higher for a better view) Compatibility with 280+ Marketplace materials Compatibility with S5 project files (no reslicing needed) And a whole lot more The UltiMaker S7 also includes quality of life improvements: We also reversed the front fan direction (fewer plastic hairs, less maintenance), made the print core door magnets stronger, and add a sensor that helps avoid flooding. This effectively makes it much harder to not achieve a perfect first layer, improving overall print success. The re-engineered print head has an inductive sensor which reduces noise when probing the build plate. Along with that, 4 pins and 25 magnets make it easy to replace the flex plate perfectly – even with one hand. But we also don’t recommend using or adhesion structures for UltiMaker materials (except PC, ’s PC). Not only do you not need tools to pop a printed part off. A PEI-coated flexible steel build plate makes a big difference to productivity. The build stack has also been completely redesigned. To further enclose the build chamber the S7 only has one magnetically latched door. This filters the exhaust air of every print and also improves build temperature stability. It now includes an integrated Air Manager. The UltiMaker S7 is built on the success of the UltiMaker S5 and its design decisions were heavily based on feedback from customers. My Question is, if there's a possibility to include this addition of S30 to the M0 Code in the script.Įither permanent or with a separate Radio-button in the script parameters. To achive this, I manually modified the generated G-code file as follows. When you dont press "Pause", within 30 seconds of the first beep, the printer directly continues with extruder priming and printing. After pressing "Resume" the printer primes the extruder and continues the work. screen with "Resume"-Button is shown followed be some beeps. ![]() Then z-axis lifts for the internal "Pause"- move Printer Goes to park position, lift-up and Beepģ.) No Motors Enganged, Disarm timeout (0) - not workingĤ.) No Motors Enganged, Disarm timeout (0), G-code before Pause ((G4 S30) - not workingĥ.) No Motors Enganged, Disarm timeout (0), + manual modification in gcode file ( M0 S30) - Working This state last for minimum 1 hour - because of "M84 S3600 Keep steppers engaged for 1h" After pressing "Pause-Button- printer displays " Paused, waiting for cache command to complete" When you press the "Pause"-Button - printer displays " Paused, waiting for cache command to complete"ġ.) Keep Motors enganded (3600s) - not working When reaching the pause layer, the printer goes to park position, lift-up and Beep General: Kobra Printer only stops for longer time, when "Pause"-Button on the display is pressed. This is, because Anycubic seems to not have proper installed M0 code.įinaly I found one setup with manual gcode adjustment that workes for me. The PauseAtHeight breaks were programmed for layer 25 and 50 of total 75 layers.įirst I tried several setups of the PauseAtHeight script and no one, worked on my Kobra. Printing with different colors on my Anycubic Kobra with PauseAtHeight drove me nuts.įor testing I used a testcylinder with D=10mm and H= 15mm. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |